Release Simcenter FloEFD version 2019.1

Release Simcenter FloEFD version 2019.1

We are pleased to announce that FloEFD, FloEFD for CATIA V5, FloEFD for Creo, FloEFD for NX and FloEFD for Solid Edge version 2019.1 are now available to download from SupportCenter!


Release Highlights

  • Fan derating. Fans are often set to run below their maximum capacity, to reduce noise and increase their lifetime, but still achieve thermal cooling requirements. Fans are run at less than maximum capacity by reducing the RPM that they operate at. This has the effect of derating (reducing) the fan curve and is simulated using the Derating factor.
  • Logical Expressions in Formula Dependency. Boundary conditions can be dependent on coordinates, time and monitor parameters such as goals. It is now possible to define sophisticated dependencies using conditional and Boolean expressions such as IF, AND, OR, XOR, NOT, > (more than), < (less than), = (equal two). For example, you can easily set a value of a heat source dependent on two different temperature sensors (defined as temperature goals) so that the dissipated power is downgraded depending on the temperature at either one or another sensor.
  • Altitude. The atmospheric pressure and temperature can be defined by setting the Altitude. Using the Altitude it is now much easier to conduct what-if or optimization analysis.
  • Additional Rays for Radiation Sources. You can now add additional rays launched from a radiation source (for Monte Carlo radiation only). This allows for better resolution of radiation or light locally without significant increasing the total number of rays and therefore saving the calculation time. In addition, radiation freezing can be enabled automatically.
  • Network Assembly. Node power can now be dependent on Temperature.


Via SupportCenter you can check all the Simcenter FloEFD Release Notes.


For more information please call us or send us an email




28th April 2021 Supply Chain Application
21st April 2021 Release Polarion ALM 21 R1
12th November 2020 Release HyperLynx VX.2.8
12th November 2020 Release Xpedition VX.2.8
12th November 2020 Release PADS VX.2.8
15th October 2020 Release Polarion ALM 20 R2
16th April 2020 DownStream Release Update
10th March 2020 What's New in PADS VX.2.7
26th September 2019 DownStream Release Update
23rd September 2019 Polarion ALM 19.2 Release
10th September 2019 Mentor VX.2.6. Release
10th April 2019 Release Polarion ALM 19
24th January 2019 Release Sherlock 6.1
18th December 2018 Release FloEFD Version 18.0
26th September 2018 BOM Connector 8 Released
17th September 2018 Xpedition® - VX.2.4 Released
14th September 2018 PADS VX.2.4. released
11th September 2018 HyperLynx VX.2.4 Released
7th September 2018 FloTHERM® ΔTJ Award
13th March 2018 New Release FloMASTER V9.0
26th February 2018 New Release PADS VX.2.3
8th February 2018 FloEFD Frontloading CFD Award
14th November 2017 New Release FloTHERM XT V3.1
21st August 2017 BOM Connector 7.6 Released
20th July 2017 Release of FloTHERM v12
29th August 2016 PADS VX.2 Now Available
29th February 2016 Sherlock User Forum
1st February 2016 TLA Winner 2015
4th August 2015 New PADS Solutions!
29th June 2015 UVM Framework
23rd June 2015 PCB Sketch Router
21st April 2015 HDL Designer 2015.1 Release
19th February 2015 BOM Connector™
14th December 2014 Multi-board PCB Systems Design
9th September 2014 New course: Introduction to UVM
20th May 2014 Mentor PCB Forum
18th March 2014 Xpedition VX release
3rd February 2014 DfR Solutions - Best of 2013
22nd October 2012 Dongle discontinuations
19th October 2012 PADS 9.5 Now Available!
20th April 2011 Introducing Questa Core
1st February 2011 PADS 9.3 available
22nd November 2010 Why customers choose BluePrint
30th June 2010 PADS9.2 Available
8th June 2010 5 Reasons to Adopt PLM
18th March 2010 Mentor-Valor Acquisition
15th February 2010 InnoFour goes Scandinavia
18th January 2010 PADS v9.1 available
9th October 2009 CAM350 v10.1 available
26th May 2009 Introducing PADS v9.0
2nd February 2009 CAM350-150 Bundle Introduction